EN 
ES
AR
NL
JA
KO
FR
RU
KDC-A04-006-60 SPST momentary 8A power push button switch with ENEC
Series:PS-12E05 series
Quick Detail:
This specification is applied to PS4-B202-60 Power Switch used for electronic equipment.
Operating temperature range:0
403. That’s an error.
We're sorry, but you do not have access to this page. That’s all we know.
Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
- Remarks
- Applications
- Technical parameters
Remarks
-
PARTS LIST:
NO.
quantity
Name
Material
1
1
Case
T375J(UL94V—0)
2
1
Handspike
PBT/PET(UL94V—0)
3
1
Cover
Armor Plate, Nickel plated
4
1
Spring holder
1Cr18Ni9Ti
5
1
Spring V
QBe2
6
1
Fulcrum
H62, Silver plated
7
1
Contact arm
H62, Silver plated
8
1
Moving contact
AgNi10/Cu
9
1
Contact arm
H62, Silver plated
10 1 Terminal
H62, Silver plated 11 1 Fixed contact
AgNi10/Cu
12 1 Spring
Beryllium alloy Qbe2
13 1 Releasing spring
72A，Nickel plated
Returned plastic should not exceed 20%.
Applications
-
Application
This specification is applied to PS-12E05 Power Switch used for electronic equipment.
Error 403 (Forbidden)!!1 403. That’s an error.
We're sorry, but you do not have access to this page. That’s all we know.
Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature 15~35℃
Technical parameters
3 General 403. That’s an error. We're sorry, but you do not have access to this page. That’s all we know.
3.1.1 Application This specification is applied to PS-22E05 Power Switch used for electronic equipment.
3.1.2 Operating temperature range 0
3.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
3.2Appearance construction and dimensions
3.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
3.2.2Construction and dimensions Refer to individual product drawing.
Trip 2.5±0.5mm
Contact pressure ≥0.4N
The deviation in contact center no large than a quarter of contact diameter
Gap≥2.5mm
Drive type Press button kind, self-lock singe reset mechanical system
3.3. Electrical specifications
|
NO. |
Items |
Test conditions |
Criteria |
|
3.3.1 |
Contact resistance |
MEASURED AT 1 KHz SMALL CURRENT(100 mA OR LESS)
|
50mΩ MAX 50毫欧以下。 |
|
3.3.2 |
Insulation resistance |
APPLY A VOLTAGE OF 500V DC SHALL BE APPLIED FOR 1 MIN AFTER WHICH MEASUREMENT BE MADE: (1) BETWEEN TERMINAL. (2) BETWEEN INDIVIDUAL TERMINAL AND FRAME.
|
100MΩ MIN
|
|
3.3.3 |
Voltage proof |
AC 500V rms(50~60Hz) FOR 1 MIN TRIP CURRENT: 0.5 mA 1)BETWEEN TERMINAL. 2)BETWEEN INDIVIDUAL TERMINAL AND FRAME.
|
WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC.
|
3.4 Mechanical characteristic
|
Item |
Description |
Test Conditions |
Standards |
|
1 |
Terminal strength |
A STATIC LOAD OF 300 gf SHALL BE APPLIED TO THE TERMINAL FOR 15 SEC. IN ANY DIRECTION.
|
THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY.ELECTRICAL AND MECHANICALCHARACTERISTICS SHALL BE SATISFIED. |
|
2 |
DISPLACEMENT OF ACTUATOR （KNOB）
|
A STATIC LOAD OF 10N（1Kgf）SHALL BE APPLIED TO THE TOP OF THE ACTUATOR(KNOB) AND THEN DISPLACEMENT SHALL BE MEASURED TO THE DIRECTION OF THE ARROW. |
THE LEVER SHALL HAVE NO ANFUNCTION IS NORMALLY.
|
|
3 |
LIFE TEST
|
WITHOUT LOAD: AN ACTUATOR SHALL BE SUBJECT TO 10,000 CYCLES AT A SPEED OF 15~18 CYCLES FOR 1 MIN.
|
1)CONTACT RESISTANCE 100 mΩ MAX 2）INSULATION RESISTANCE 50MΩ MIN. 3）WITHSTAND VOLTAGE AC 500V, 1 MINUTE. （4）OPERATING FORCE ±30% INITIAL VALUE. （5）WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC.
|
3.5. Durability
3.6. Welding Performance
|
3.6.1 |
Solder ability |
THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 235±5 °C FOR 3±0.5 SECONDS.
|
The area of dip tin should capture the 75% impregnated area |
|||||||||
|
3.6.2 |
Resistance to soldering heat |
The switch will be inspect under such conditions below Temperature and impregnated time
(2) TMMERSION DEPTH: IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6 mm.
|
WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OFTERMINALS MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
|
|||||||||
|
3.6.3 |
HEAT TEST
|
THE JACK SHALL BE STORED AT A TEMPERATURE OF 85±2 °C FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE.
|
||||||||||
|
3.6.4 |
COLD TEST
|
THE JACK SHALL BE STORED AT A TEMPERATURE OF -10±2 °C FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE.
|
4. DRAWING & DIMENSION: