+86-0512-62885849

جميع الفئات

المنزل /منتجات /مفتاح الفصل الكهربائي

  • /img/ne8014-tncq-h-sw3p-1ways-3-pins-metal-on-off-on-on-rocker-arms-toggle-switch.jpg

NE8014-TNCQ-H-SW3P 1 طرق 3 دبابيس معدنية ON-OFF-ON ذراع الروك تبديل تبديل

سلسلة:NE8014-TNCQ-H-SW3P

تفصيل سريع:

نوع: NE8014-TNCQ-H-SW3P
تقييم الموقع: 5A@125 VAC أو28VDC (Q جهة الاتصال)
وظيفة:1P2T
نموذج المحطة الطرفية: PCB الطرفية
حماية: الامتثال  IP65

  • ملاحظات
  • تطبيقات
  • المعلمات التقنية
ملاحظات

قائمه الأجزاء:

لا.

اسم

مواد

1

قاعدة البلاستيك

نايلون

2

المحرك

نايلون النحاس سبيكة,مطلي الكروم مع الداخلية O-حلقة القياسية؛النايلون

3

حاوية بلاستيكية

نايلون

4

إنهاء جهات الاتصال

سبائك النحاس, مطلي بالفضة (Q مواد الاتصال )

5

جهات اتصال المركز & جميع المحطات الطرفية

سبائك النحاس, مطلي بالفضة (Q مواد الاتصال)

6

ختم المحطة الطرفية

الايبوكسي

7

البندق & قفل حلقة

النحاس,النيكل مطلي

8

قفل غسالة

صلب

تطبيقات

1.المنتجات الرقمية: كاميرا رقمية, الفيديو الرقمي وهلم جرا;   

2.جهاز التحكم عن بعد: التحكم عن بعد من منتجات الأمن المنزلي السيارات;   

3.منتجات الاتصالات: هاتف محمول, مركبه محموله علي الهاتف, مجموعه الهاتف, معدات البناء, المساعد الشخصي الرقمي وهلم جرا;  
                                             
4.الاداات المنزلية: مجموعه التلفزيون, فرن الميكروويف, الأرز الكهربائية طباخ, مراوح كهربائيه ,الثلاجه,غساله;تكييف الهواء وهلم جرا;   
                                                                              
5.منتجات الأمن: البصرية انترفون, رصد وهلم جرا;   
                      
6.ألعاب الأطفال: اللعب الكهربائية وهلم جرا;   

7.منتجات الكمبيوتر: كاميرا الكمبيوتر وهلم جرا;   

8.آلات تمارين: المطاحن, تدليك كرسي وهلم جرا;                                                                    

9.الجهاز الطبي: مقياس ضغط, ميزان الحرارة, نظام استدعاء المستشفى وهلم جرا;
      
10.الآخرين:  الليزر القلم ,مؤشر,الماوس لاسلكيه التحكم عن بعد القلم,الليزر إسقاط القلم,الصفحة تيرنر,القلم الكترونيه ؛ قلم الماوس ؛ الإسقاط العلوي وهلم جرا;

11.مفاتيح التشغيل في جميع أنواع المعدات الكترونيه مثل الاجهزه السمعية, أجهزه مكتبيه, أجهزه الاتصالات, أدوات القياس, تلفزيونات, مسجلات الفيديو,السيارات مجموعات, إلخ.

12.المنزليه, القوه الكهربائية, الاتصالات السلكيه, اله أداه, وعاء, المنسوجات, طبع, اله التعدين,  اله موسيقيه, إلخ.

المعلمات التقنية

1. تفاصيل المواصفات:

نوع:                NE8014-TNCQ-H-SW3P

تقييم الموقع:          5A@125 VAC أو28VDC (Q جهة الاتصال)

وظيفه:        1P2T 

1.1 مبرمج من اختبار:

خصوصيه

بند

وصف

اختبار  حاله

الاحتياجات

电气 特性

1.1.1

الفحص البصري

عن طريق فحص البصرية دون أي ضغط والاختبار

لا يجب أن يكون هناك عيب يؤثر على وظيفة المنتج

1.1.2

الاتصال المقاومة

(1)To be measured between the two terminals associated with each switch pole.

②Measurements shall be made with a 1kHz shall current contact resistance meter.

10mΩ MAX(initial)

1.1.3

Insulation Resistance

500VDC,1min±5sec

1000MΩ  MIN

1.1.4

Dielectric withstanding voltage

1500VAC (50Hz or 60 Hz) shall be applied between all the adjacent terminals and between the terminal and the frame for 1 minute.

There shall be no breakdown or flashover

机械特性

1.1.5

Operating Force

Applied in direction operation

ON→OFF

OFF→ON

 

10N max

1.1.6

Stop Strength

A static load of 30N is applied in the operating direction and pulling direction operated for a period of 30 seconds.

There shall be no sign of damage mechanically

1.1.7

Soldering Heat Resistance

(1) 焊温Soldering Temperature:260±5°C

(2) 浸焊时间Duration of Solder Immersion:5±1 sec

(3) 焊锡操作之次数,最多2次Frequency of Soldering Process,2 times Max

(PCB厚度为1.6mm)

PCB is 1.6mm in thickness

As show in item2~6

耐久性

1.1.8

寿命测试

Operation Life

测试时需依照下列所设定情况

施以3A,250V之交流电

‚作动速度:6~8回/min

ƒ受测次数:6000回

Measurements shall be made following the test set forth below:

3A,250VAC resistive load

‚Rate of Operation:6~8cycles/minute

ƒCycle of Operation:6000cycles

受测后之成品仍需符合前述3~4测试项规格之要求

As show in item 3.4

耐候性

1.1.9

耐寒性

Resistance Low Temperature

  请依照下列所设定的条件测试后.并于常温常湿中放置1小时后测定

受测温度:-30±3°C

‚受测时间:48小时

Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made
Temperature:-30±3°C

‚Time:48 hours

受测后之成品仍需符合前述2~6测试项规格之要求

As show in item 2~6

1.1.10

Resistance high Temperature

Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made
Temperature:85±3°C

‚Time:48 hours

1.1.11

耐湿性

Resistance Humidity

请依照下列所设定的条件测试后.并于常温常湿中放置1小时后测定

受测温度:40±2°C

‚相对湿度:90-95%

ƒ受测时间:48小时

Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made
Temperature:40±2°C

‚Relative Humidity:90-95%

ƒTime:48 hours

1.受测后之成品仍需符合前述4~6测试项规格之要求

2.经过测试后之接触阻抗值不得高于100mΩ

3.受测后之绝缘阻抗不得低于10MΩ

1.As show in item 4~6

2. Contact Resistance:100mΩ max

3.Insulation Resistance:10MΩ min

Actuating Force:

The force required to move the actuator from the free to the operation position

 

1.2 GENERAL CHARACTERISTICS

1.2.1 Application: This specification is applied to 6021 Toggle Switch used for electronic equipment.

1.2.2 Operating temperature range: 0℃ + 105℃

1.2.3 Test conditions : Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows  

Ambient temperature:                      15~35℃

Relative humidity:                           45~85%

Air pressure:                                   86~106kPa (860~1060 mbar)

1.3 APPEARANCE, STRUCTURE AND DIMENSION

1.3.1 Appearance :Switch shall have good finishing, and no rust crack or plating failures.

1.3.2 Construction and dimensions: Refer to individual product drawing.

1.4. Electrical specifications

NO.

ITEM

TEST CONDITIONS

PERFORMANCE

1.4.1

Contact

resistance 

 

The 2-4VDC is tested under tiny current (below 100mA), silver plated or gold plated.

20mΩ MAX

1.4.2

Insulation

resistance

 

Input 500V DC voltage for 1 minutes, test according to the following contact mode:

(1)Between the terminal.

(2)Between the terminal and the outer shell.

100MΩ MIN

1.4.3

Pressure resistance

Measurement of AC 1500V (50-60 Hz) between open contacts and poles

Measurement of AC 3000V (50~60Hz) between terminal and grounding

Fixed time: 1 minute each

 

No abnormality, such as insulation damage


1.5 Endurance

NO.

ITEM

TEST CONDITIONS

PERFORMANCE

1.5.1

Load life (A)

(UL1054 standard)

16A 125VAC

The switch is tested in the order of Test 1 and Test 2.

 

Voltage

Steady current

power factor

Test 1

125V

20A

0.75~0.8

Test 2

125V

16A

0.75~0.8

 

 

Opening and closing speed(cycles/min)

Opening and closing speed(cycle)

Test 1

6~10

50

Test 2

6~10

6,000

 

 

 

After Experiment 2:

The rated current and insulation resistance can be switched on and off after the test. (1.5.2)100MΩMin. Withstand voltage AC 1000V No insulation damage after 1 minute test, Operating Force(1.1.1)Within the range of + 10% or - 30% of specifications. No abnormal appearance structure, Temperature rise: below 30℃ Max

 

 

 

1.5.2

 

Load life (B)

(UL1054 standard)

 

10A 277VAC

The switch is tested in the order of Test 1 and Test 2

 

Voltage

Steady current

power factor

Test 1

277V

15A

0.75~0.8

Test 2

277V

10A

0.75~0.8

 

 

Opening and closing speed(cycles/min)

Opening and closing speed(cycle)

Test 1

6~10

50

Test 2

6~10

6,000

 

 

C 1000V No insulation damage after 1 minute test, Operating Force(1.1.1)Within the range of + 10% or - 30% of specifications. No abnormal appearance structure, Temperature rise: below 30℃ Max

 

 

1.6 ENVIRONMENT RESISTANCE

NO.

ITEM

TEST CONDITIONS

PERFORMANCE

1.6.1

Cold tolerance test

    It was placed at a temperature of -20±2℃, and then placed in normal room temperature for 1 hours after 96 hours.

Contact resistance:100nΩMax.

Insulation resistance:100MΩMin.

Pressure resistance:

Measurement of AC 1500V (50-60 Hz) between open contacts and poles

Measurement of AC 3000V (50~60Hz) between terminal and grounding

Fixed time: 1 minute each Operating Force(3.1.1)Within the range of + 10% or - 30% of specifications. No abnormal appearance structure, No abnormalities such as insulation damage

1.6.2

Heat resistance test

It was placed at a temperature of 85 + 2℃, and then placed at normal room temperature for 1 hours after 96 hours.

 

1.6.3

Moisture resistance

 In the environment of 40 2 C and 90 ~ 95% relative humidity, the determination was carried out within 1 hour in room temperature and humidity.

1.7 SAFEKEEPING METHOD:

(1)If the product is not used immediately, it should be kept at normal temperature without direct sunlight and corrosive gases.

In the environment. But we recommend that we use it as soon as 6 months.

(2)Put the finished products in plastic bags and seal them in the same environment as soon as possible, and use them as soon as possible. Do not overlay excess when saved in order to prevent the pressure from breaking.

(3)Do not overlay excess when saved in order to prevent the pressure from breaking.

2. DRAWING & DIMENSION:

CIRCUIT DIAGRAM:

Contact Us