PS-12E15 single pole momentary push button switch with 3 pins
Series:PS-12E05 series
Quick Detail:
This specification is applied to PS-22E15 Power Switch used for electronic equipment.
Operating temperature range: -10
403. That’s an error.
We're sorry, but you do not have access to this page. That’s all we know.
Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature: 15~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
- Remarks
- Applications
- Technical parameters
Remarks
-
SAFETY APPROVAL & RATING:
Approved Rating
Mark
Reference No.
TV8/120VAC TV-8 125VAC 10T85 10GPA 125/250VAC 10A 125/250VAC
1E4 10T85
UL&CUL
E176213
4A/128A 250VAC 10T85 1E4
VDE
129571
8A/128A 250VAC 1E4
CQC
CQC02002002689
4A/128A 250VAC 10T85 1E4
NEMKO
P10213186
4A/128A 250VAC 10T85 1E4
SEMKO
1021831
4A/128A 250VAC 10T85 1E4
FIMKO
261487
4A/128A 250VAC 10T85 1E4
DEMKO
314333-02 D-03541
4A/128A 250VAC 10T85 1E4
CE
SH10041366-V1
TUV
10A 125/250VAC 1E4 10T85
ENEC
ENEC-00946
4/128A 250VAC 10T85 1E4
EK
SU0230-7006A
10A 125/250VAC 1E4 10T85
CB
SE-51323 DK-40111-UL
PARTS LIST:
NO.
quantity
Name
Material
1
1
KONB
POM
2
1
BLOCK
STEEL STRIP
3
1
SPRING
SUS
4
1
CAM STICK
PBS WIRE
5
1
SPRING PLATE
PBS STRIP
6
1
FRAME
STEEL STRIP
7
1
BASE
PHENOLIC RESIN
8
1
TERMINAL
BRASS STRIP
9
1
CONTACT
PBS C5210R-EH
Returned plastic should not exceed 20%.
Applications
This specification is applied to PS-12E05 Power Switch used for electronic equipment. 403. That’s an error. We're sorry, but you do not have access to this page. That’s all we know.
Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature 15~35℃
Technical parameters
3 General 403. That’s an error. We're sorry, but you do not have access to this page. That’s all we know.
3.1.1 Application This specification is applied to PS-22E05 Power Switch used for electronic equipment.
3.1.2 Operating temperature range -10
3.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
3.2Appearance construction and dimensions
3.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
3.2.2Construction and dimensions Refer to individual product drawing.
Trip 2.5±0.5mm
Contact pressure ≥0.4N
The deviation in contact center no large than a quarter of contact diameter
Gap≥2.5mm
Drive type Press button kind, self-lock singe reset mechanical system
3.3. Electrical specifications
NO. |
Items |
Test conditions |
Criteria |
3.3.1 |
Contact resistance |
MEASURED AT 1 KHz SMALL CURRENT(100 mA OR LESS)
|
30mΩ MAX 30毫欧以下。 |
3.3.2 |
Insulation resistance |
APPLY A VOLTAGE OF 500V DC SHALL BE APPLIED FOR 1 MIN AFTER WHICH MEASUREMENT BE MADE: (1) BETWEEN TERMINAL. (2) BETWEEN INDIVIDUAL TERMINAL AND FRAME.
|
100MΩ MIN
|
3.3.3 |
Voltage proof |
AC 500V rms(50~60Hz) FOR 1 MIN TRIP CURRENT: 0.5 mA 1)BETWEEN TERMINAL. 2)BETWEEN INDIVIDUAL TERMINAL AND FRAME.
|
WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC.
|
3.4 Mechanical characteristic
Item |
Description |
Test Conditions |
Standards |
1 |
Terminal strength |
A STATIC LOAD OF 300 gf SHALL BE APPLIED TO THE TERMINAL FOR 15 SEC. IN ANY DIRECTION.
|
THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY.ELECTRICAL AND MECHANICALCHARACTERISTICS SHALL BE SATISFIED. |
2 |
DISPLACEMENT OF ACTUATOR (KNOB)
|
A STATIC LOAD OF 10N(1Kgf)SHALL BE APPLIED TO THE TOP OF THE ACTUATOR(KNOB) AND THEN DISPLACEMENT SHALL BE MEASURED TO THE DIRECTION OF THE ARROW. |
THE LEVER SHALL HAVE NO ANFUNCTION IS NORMALLY.
|
3 |
LIFE TEST
|
WITHOUT LOAD: AN ACTUATOR SHALL BE SUBJECT TO 10,000 CYCLES AT A SPEED OF 15~18 CYCLES FOR 1 MIN.
|
1)CONTACT RESISTANCE 100 mΩ MAX 2)INSULATION RESISTANCE 50MΩ MIN. 3)WITHSTAND VOLTAGE AC 500V, 1 MINUTE. (4)OPERATING FORCE ±30% INITIAL VALUE. (5)WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC.
|
3.5. Durability
3.6. Welding Performance
3.6.1 |
Solder ability |
THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 230±5 °C FOR 3±0.5 SECONDS.
|
The area of dip tin should capture the 75% impregnated area |
|||||||||
3.6.2 |
Resistance to soldering heat |
The switch will be inspect under such conditions below Temperature and impregnated time
(2) TMMERSION DEPTH: IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6 mm.
|
WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OFTERMINALS MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
|
|||||||||
3.6.3 |
HEAT TEST
|
THE JACK SHALL BE STORED AT A TEMPERATURE OF 70±2 °C FOR 48 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE.
|
||||||||||
3.6.4 |
COLD TEST
|
THE JACK SHALL BE STORED AT A TEMPERATURE OF -25±3 °C FOR 48 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE.
|
4. DRAWING & DIMENSION:
5. CIRCUIT DIAGRAM: