EN 
ES
AR
NL
JA
KO
FR
RU
3AS1SWR102M1RES free sample ON-OFF 3 pins round waterproof rocker switch
Series:3AS1
Quick Detail:
Type: 3AS1SWR102M1RES
Construction category: D
Operation method: Rocker Action
Configuration: Single-Pole Single-Through (SPST)
Terminal form: #PCB-connect Terminal
Mounting: Snap-In
Protection: IP67
- Remarks
- Applications
- Technical parameters
Remarks
-
SAFETY APPROVAL & RATING:
Approved Rating
Mark
Reference No.
UL&CUL
VDE
CQC
NEMKO
SEMKO
FIMKO
DEMKO
CE
TUV
ENEC
EK
CB
PARTS LIST:
ITEM
NAME
MATERIAL
1
Case & Bushing Glass filled nylon 6/6,flame retardant, heat stabilized(UL94v-0).
2
Actuator
Nylon black std. Internal O-ring seal standard with all actuactors.
3
Frame
Spring steel, black std.
4
Switch support
Brass or steel, tin plated.
5
Terminals/contact
Silver or gold plated. Copper alloy
6
Actuator pivot & mounting bracket
Brass, with silver or gold plated
7
Actuator pivot retainer Stainless steel Returned plastic should not exceed 20%.
Applications
Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.
Electronic Equipment
Toys, Power tools, Car control panel etc.
Medical Equipment
Communication Equipment
Automation Equipment
Automotive Electronics
Instrumentation
Technical parameters
1.DETAIL SPECIFICATIONS:
Type:3AS1SWR102M1RES
Construction category:D
Operation method:Rocker Action
Configuration:Single-Pole Single-Through (SPST)
Terminal form:#187 quick-connect Terminal
Mounting:Snap-In
Protection:IP65
1.1OPERATING CHARACTERISTICS
|
Characteristics |
Units |
Standards |
Note |
|
Actuating Force |
N |
3.5±1 Max |
Original 3.5±1 |
|
Contact Force |
N |
0.4 Min |
Original 0.4 Min |
|
Electrical Clearance |
mm |
3 Min |
Original 3 Min |
Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
1.2.1Application This specification is applied to KAN Rocker Switch used for electronic equipment.
1.2.2 Operating temperature range -25℃ to +105℃
1.2.3Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications
|
NO. |
Items |
Test conditions |
Criteria |
|
1.4.1 |
Contact resistance |
The contact resistance should be 10mΩ(Max). |
10mΩ MAX |
|
1.4.2 |
Insulation resistance |
It is measured with 500V DC 1minute should be 1000MΩ(Min). |
100MΩ MIN |
|
1.4.3 |
Voltage proof |
AC 2000V,1min.(before endurance test) AC 1500V,1min.(after endurance test)
|
No dielectric breakdown shall occur |
1.5. ENVIRONMENT RESISTANCE
|
NO. |
Item |
Test conditions |
Criteria |
|
1.5.1 |
Cold |
After testing at -25±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. |
Contact resistance (item 4.1): 20mΩ MAX Insulation resistance (item 4.2): 100MΩ MIN Voltage proof: (item 4.3) No dielectric breakdown shall occur. Operating characteristic (item 5.1): Operating characteristic variety Within ±10% of specified value . No abnormalities shall be recognized in appearance and construction. |
|
1.5.2 |
Dry heat |
After testing at 105±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. |
|
|
1.5.3 |
Damp heat |
After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. |
|
|
1.5.4 |
Change of temperature |
After 20 cycles of following conditions the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. |
|
|
1.5.5 |
Salt mist |
Switch shall be checked after following lest. 1) Temperature: 35±2℃ 2) Salt solution: 5±1% (solids by mass) 3) Duration: 24±1h After test, salt deposit shall be removed in running water |
No remarkable corrosion shall be recognized in metal part |
1.6. WELDING CHARACTERISTICS
|
1.6.1 |
Solder ability |
Switch test under such conditions and inspect after. 1）Variable temperature range ：235±5℃； 2）Dip time：3±0.5s； |
The area of dip tin should capture the 95% impregnated area |
|||||||||
|
1.6.2 |
Resistance to soldering heat |
The switch will be inspect under such conditions below Temperature and impregnated time
|
All of the appearance, motor functions, electrical properties are no abnormal. |
1.7. ENDURANCE
|
NO. |
Item |
Test condition |
Criteria |
||||||||||||||||||
|
1.7.1 |
Endurance (According to UL61058) |
5A 120VAC 2A 250VAC Switch shall be operated according to following sequence (Test1~Test2)
Voltage proof(Cut-off current:0.5mA) 5A 120VAC 2A 250VAC Switch shall be operated 30,000 cycles at 15-20 cycles/min. Test voltages shall be applied for 1 min
|
Insulation resistance (item 4.2): 100MΩ MIN Voltage proof: Terminal and ground: 1000VAC No dielectric breakdown shall occur. Operating characteristic (item 5.1): Operating characteristic variety Within ±20% of specified value . 6000 cycles temperature rise:30℃ MAX; 10,000 cycles temperature rise:55℃ MAX;
No abnormalities shall be recognized in appearance and construction |
||||||||||||||||||
|
1.7.2 |
Endurance (According to EN61058-1 /IEC61058-1) |
5A 120VAC 2A 250VAC Switch shall be operated 30,000 cycles at 15~20 cycles/min Voltage proof(Cut-off current:0.5mA) Test voltages shall be applied for 1 min.
|
Insulation resistance (item 4.2): 100MΩ MIN Voltage proof: Terminal and terminal:750VAC Terminal and ground:1500VAC No dielectric breakdown shall occur. Operating characteristic (item 5.1): Operating characteristic variety Within ±20% of specified value . Temperature rise:55℃ MAX No abnormalities shall be recognized in appearance and construction |
1.6. SOLDERING
Solder ability and Resistance to sold heat according to IEC 68-2-20
2. DRAWING & DIMENSION:
3. PACKING:
|
3.1 |
Packing material: |
Plastic bag |
|
3.2 |
Packing number: |
100 pieces per bag Each shipping carton 2000 pieces |
|
3.3 |
Weight: |
Gross Weight: 13.75kg Net Weight: 12.56kg |
|
3.4 |
Size: |
31 x26 x27 CM /0.022CBM |