DC-012A DC socket, DC power jack，pass GWFI 850°C

Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.
Electronic Equipment
Toys, Power tools, Car control panel etc.
Medical Equipment
Communication Equipment
Automation Equipment
Automotive Electronics
Instrumentation

Type: DC-012A

Rating: DC30V 2.0A

2.1外觀、結構和尺寸 

2.1.1外觀                    開關外觀完好，無銹蝕、裂紋和鍍層缺陷。

Appearance：Switch shall have good finishing, and no rust crack or plating failures.

2.1.2結構和尺寸              參見相應的產品圖樣

Construction and dimensions : Refer to individual product drawing.

2.2. 電氣性能Electrical Characteristics: 

條號	項目	測試條件	標準
2.2.1	接觸電阻CONTACT RESISTANCE	在1KHZ 小電流下測量 Being measured at 1KHz small current contact resistance meter.	30 毫歐以下. 30mΩ MAX
2.2.2	絕緣電阻INSULATION RESISTANCE	在端子之間和端子與殼之間加DC 500V條件下,持續1 分鐘測量. Measurements shall be made following application of DC500V potential across terminals and across terminals and frame for 1 minute.	100 兆歐以上. 100MΩ MIN
2.2.3	耐壓WITHSTAND VOLTAGE	在端子之間和端子與殼之間加 500V(50HZ 或60HZ)條件下,持續 1 分鐘測 量 AC 500V (50Hz or 60Hz) shall be applied across terminals and across terminals and frame for one minute.	沒有發生介質擊穿現象 There shall be no breakdown

 

2.3. 耐久性Endurance Characteristics 

條號	項目	測試條件	標準
2.3.1	可焊性試驗SOLDERI NG TEST.	端子頂部被浸入焊錫池2mm 深,溫度230±5℃時間3±0.5 秒。 The tip of the terminals shall be dipped 2mm in the solder bath at a temperature of 230±5 ℃ for 3±0.5sec	浸入的部分90%以上表面將被錫 覆蓋. A new uniform coating of solder shall cover a minimum of 90 of the surface being immersed
2.3.2	壽命試驗LIFE TEST.	無負載條件下,每分鐘20-30 次的速度操作5,000 次。5,000 cycles of operation at a rate of 20-30 cycles per minute with unloading.	(1). 接觸阻抗40 毫歐以下.Contact resistance . 40mΩmax (2). 插拔力變化範圍初始值30% Insertion and withdraw force 30 initial value (3). ITEM 專案-4B (4). ITEM 專案-4C (5). ITEM 專案-5B
2.3.3	耐熱試驗HEAT TEST.	在85±2℃環境中放48 小時,再放在正常環境中30 分鐘後進行測試。85 ± 2 ℃ for 48 hours after test keep in normal condition for 30 minutes.	(1). 接觸電阻50 毫歐以下Contact resistance 50mΩ max. (2). 絕緣電阻50 兆歐以上Insulation resistance. 50M Ω min. (3). 無任何迹象顯示機械及電器性能之損壞.There shall be no sign of damage mechanically and electrically.
2.3.4	耐濕試驗HUMIDITY TEST.	在89% RH 環境中放48 小時,再放在正常環境中30 分鐘後進行測試。89% RH for 48 hrs. after test keep in normal condition for 30 min
2.3.5	耐冷試驗COLD TEST.	在-40±2℃環境中放48 小時,再置於正常環境中30 分鐘後進行測試。At –40 ± 2℃ for 48 hrs. after test keep in normal condition for 30 min.

 

2.4. 機械性能Mechanical Characteristics 

2.4.1	插拔力INSERTION AND WITHDRAW FORCE	用測力計在插頭與彈片之間進行測量Being measure at across spring piece and across matching plug for ergometer	插拔力5-18N Insertion and extraction force 5-18N
2.4.2	端子強度TERMINAL STRENGTH	一個500 克之靜負荷施加於端子頂部的一個方向持續1 分鐘。A static force of 500gf being applied in one direction on the tip of terminal for 1 minute.	無任何迹象顯示機械及電氣性能之損壞.There shall be no sign of damage mechanically and electrically

5.DRAWING & DIMENSION: