047-487-0552

EN
すべてのカテゴリ

ホーム /製品案内 /ディップスイッチ /DTS

SW50-DTS-EMR-06 6Pins Code Switch DIP Switch Piano Push Switch

シリーズ:SW10-DS-06

クイック詳細:

詳細仕様:

タイプ: SW50-DTS-EMR-06

操作方法:DIPスイッチ

準拠:■IP40□IP65□IP67□IP68

Rating: 24DC 25mA

備考

パーツリスト:


NO

NAME

QTY

材料

1

カバー

1

High-temp. Thermoplastic PA 9T UL94V-0

2

お問い合わせ

*

3

作動装置

*

Thermoplastic LCP UL 94V-0

4

ターミナル

6

真鍮

5

ベース

1

High-temp. Thermoplastic PA 9T UL94V-0

6

テープ

1

Kapton

用途

1.Digital製品:デジタルカメラ、デジタルビデオなど。

2.Remote Control:自動車の国内セキュリティ製品のリモートコントロール。

3.Communication製品:携帯電話、車載電話、電話機、建築設備、PDAなど。

4.Homehole家電:テレビ、電子レンジ、電気炊飯器、扇風機、冷蔵庫、洗濯機、エアコンなど;

5.Security製品:視覚的なインターホン、モニターなど。

6.Toys:電気玩具など。

7.Computer製品:PCカメラなど。

8.Exercises Machines:トレッドミル、マッサージアームチェアなど。

9.Medical Device:血圧計、体温計、病院呼び出しシステムなど。

10.Others:レーザーペン、ポインター、ワイヤレスマウスリモコンペン、レーザー投影ペン、ページターナー、電子ペン、MousePen、オーバーヘッドプロジェクターなど。

11:オーディオデバイス、オフィスデバイス、通信デバイス、測定器、テレビ、ビデオレコーダー、自動車セットなど、あらゆる種類の電子機器の操作スイッチ

12。家電、電気力、電気通信、工作機械、容器、織物、印刷、マイニングマシン、楽器など

技術パラメーター

1.1 一般的な特性:

1.1.1 アプリケーション この仕様は、電子機器に使用されるDIPスイッチに適用されます。

1.1.2 動作温度範囲 -20℃+ 85℃

1。1。3 試験条件

Unless other :specified. The atmospheric conditions for making measurements and tests are as follows:

周囲温度:5〜35℃

Relative humidity: 45~85%

Air pressure: 86~106kPa (860~1060 mbar)

判断に疑問が生じた場合。 試験は次の条件で実施するものとする。

Ambient temperature: 20±2℃

相対湿度:60〜70%

空気圧:86〜106kPa(860〜1060 mbar)

1.2 外観の構成と寸法:

1.2.1 外観

スイッチの仕上げは良好で、錆割れやめっき不良はありません。

1.2.2 構造と寸法

個々の製品図面を参照してください。

1.3。 電気的仕様

項目

説明

試験条件

要件

1.3.1

Contact Resistance

1) To be measured between the two terminals associated with each switch pole.

2) Measurements shall be made with a 1kHz shall current contact resistance meter.

100mΩ MAX. (initial)

1.3.2

Insulation Resistance

500V DC, 1 minute ± 5 sec.

100MΩMIN

1.3.3

Dielectric withstand-ing Voltage

500V AC (50Hz or 60 Hz) shall be applied between all the adjacent terminals and between the terminal and the frame for 1 minute.

There shall be no breakdown or flashover.

1.3.4

キャパシタンス

1MHz±10kHz

5 pF Max

1.3.5

作戦部隊

Applied in the direction of operation.

ON→OFF

オフ→オン

1000gf Max

(9.8N Max)

1.4 ENVIRONMENT RESISTANCE:

項目

説明

試験条件

要件

1.4.1

Resistance Low Temperature

Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made :

1)Temperature : -40±3℃

2)Time: 96 hours

1)As shown in item 2.3.1-2.3.5

2)Contact Resistance:

100mΩ max.

1.4.2

Resistance High Temperature

Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made :

1) Temperature : 85±2℃

2) Time: 96 hours

1.4.4

Resistance Humidity

Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made :

1) Temperature : 40℃±2℃

2) Relative Humidity :90~95%

3) Time: 96 hours

1)As shown in item 2.3.3-2.3.5

2)Contact Resistance:

100mΩ max.

3)Insulation Resistance:

1.5 SOLDERING CONDITIONS:

■ Condition for Soldering –EM(R) Series

■ The condition mentioned above is the temperature on the Cu foil of the P.C.B surface. There are cases where board’s temperature greatly differs from switch’s surface temperature depending on board’s material, size, thickness, etc. Care, therefore, should be used not to allow switch’s surface temperature to exceed 260℃.

■ Manual Soldering

Soldering Temperature

Max.350℃

Continuous Soldering Time

Max. 5 seconds

■ Precautions in Handling

1. Care should be exercised so that flux from the upper part of the printed circuit board does not adhere to the switch.

2. Don’t clean the switch body except with top tape sealed type, which can only spray of cleaning method from top of s/w.

3. Please make sure that there is no flux rose over the surface of the PCB

1.6 DURABILITY:

1.6.1

Operation Life

Measurements shall be made following the test set forth below:

1) 25mA, 24VDC resistive load

2) Rate of Operation: 15~20 cycles/ minute

3) Cycle of Operation: 2000 cycles.

1)As show in item 2.3.2-2.3.3

2)Contact Resistance: 500mΩmax.

(final-after test)

1.6.2

Stop Strength

A static load of 1kgf is applied in the operating direction and pulling direction operated for a period of 15 seconds.

There shall be no sign of damage mechanically.

1.6.3

振動

Shall be vibrated in accordance with Method 201A of MIL-STD-202F

1) Frequency: 10-55-10 Hz 1 min/cycle.

2) Direction: 3 vertical directions including the direction of operation.

3) Test Time: 2 hours each direction.

As shown in item 2.3.1-2.3.5

2。 図面と寸法:

A=15.14; B=12.7

3. 梱包:

3.1

包装材:

Strip plate
二重層の紙の箱

3.2

梱包番号:

900 pieces per plate
3 plate per shipping carton
各出荷用カートン2700個

3.3

総重量:

Gross Weight: kg

Net Weight: kg