EN 
ES
AR
NL
JA
KO
FR
RU
KAN-B2-SW25D-R (WP) 2 pins round SPST ON-OFF rocker switch with waterproof cap
Series:KAN-B2
Quick Detail:
Type:KAN-B2-SW25D-R(WP)
Rating: 10A 125VAC10(6)A 250VAC
Operation method: Rocker Action
Configuration: Single-Pole Single-Through (SPST)
Terminal form: Solder Terminal
Mounting: Snap-In
- Remarks
- Technical parameters
Remarks
Technical parameters
1.DETAIL SPECIFICATIONS:
Type:KAN-B2-SW25D-R(WP)
Rating: 10A 125VAC10(6)A 250VAC
Operation method: Rocker Action
Configuration: Single-Pole Single-Through (SPST)
Terminal form: Solder Terminal
Mounting: Snap-In
1.1OPERATING CHARACTERISTICS
|
Characteristics |
Units |
Standards |
Note |
|
Actuating Force |
N |
4±2Max |
Original 4±2 . |
|
Contact Force |
N |
0.4 Min |
Original 0.4 Min |
|
Electrical Clearance |
mm |
3 Min |
Original 3 Min |
Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
1.2.1Application This specification is applied to KAN Rocker Switch used for electronic equipment.
1.2.2 Operating temperature range -25℃ to +105℃
1.2.3Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications
|
NO. |
Items |
Test conditions |
Criteria |
|
1.4.1 |
Contact resistance |
Shall be measured at 12A 24VDC by voltage drop method after some operations without load. Applied position: Between terminal and terminal |
100mΩ MAX |
|
1.4.2 |
Insulation resistance |
Test voltage:500VDC, measured after 1 min ±5s Applied position: 1) Between terminal and terminal 2)Between terminal and ground |
100MΩ MIN |
|
1.4.3 |
Voltage proof |
Following test voltages shall be applied for 1 min. (Cut-off current:0.5mA) 1)Between terminal and terminal :2000VAC/min (50~60Hz) 2)Between terminal and ground: 2500VAC/min (50~60Hz) |
No dielectric breakdown shall occur |
1.5. ENVIRONMENT RESISTANCE
1.6. WELDING CHARACTERISTICS
|
1.6.1 |
Solder ability |
Switch test under such conditions and inspect after. 1）Variable temperature range ：235±5℃； 2）Dip time：3±0.5s； |
The area of dip tin should capture the 95% impregnated area |
|||||||||
|
1.6.2 |
Resistance to soldering heat |
The switch will be inspect under such conditions below Temperature and impregnated time
|
All of the appearance, motor functions, electrical properties are no abnormal. |
1.7. ENDURANCE
|
NO. |
Item |
Test condition |
Criteria |
||||||||||||||||||
|
1.7.1 |
Endurance (According to UL61058) |
13A 125VAC Switch shall be operated according to following sequence (Test1~Test2)
Voltage proof(Cut-off current:0.5mA) 1GPA 125/250VAC ; Switch shall be operated 6,000 cycles at 15-20 cycles/min. Test voltages shall be applied for 1 min |
Insulation resistance: 100MΩ MIN Voltage proof: Terminal and ground: 1000VAC No dielectric breakdown shall occur. Operating characteristic : Operating characteristic variety Within ±20% of specified value . 6000 cycles temperature rise:30℃ MAX; 10,000 cycles temperature rise:55℃ MAX;
No abnormalities shall be recognized in appearance and construction |
||||||||||||||||||
|
1.7.2 |
Endurance (According to EN61058-1 /IEC61058-1) |
10 (8) A 250VAC Switch shall be operated 10,000 cycles at 15~20 cycles/min Voltage proof(Cut-off current:0.5mA) Test voltages shall be applied for 1 min. |
Insulation resistance: 100MΩ MIN Voltage proof: Terminal and terminal:750VAC Terminal and ground:1500VAC No dielectric breakdown shall occur. Operating characteristic : Operating characteristic variety Within ±20% of specified value . Temperature rise:55℃ MAX No abnormalities shall be recognized in appearance and construction |
2. DRAWING & DIMENSION:
3. Packing
|
3.1 |
Packing material: |
Plastic bag |
|
3.2 |
Packing number: |
100 pieces per bag Each shipping carton 2000 pieces |
|
3.3 |
Weight: |
Gross Weight: 13.75kg Net Weight: 12.56kg |
|
3.4 |
Size: |
31 x26 x27 CM /0.022CBM |