+86-0512-62885849

EN
All Categories

Home /Products /Rocker Switch /General Rocker Switch

KAN-D3-6 side edge terminal ON-OFF SPST rocker switch for power tools

Series:KAN-D3-6

Quick Detail:

Type:                                      KAN-D3-6    
Construction category:       D
Operation method:             Rocker Action
Configuration:                     Single-Pole Single-Through (SPST)
Terminal form:                     #187 quick-connect Terminal
Mounting:                             Snap-In
Protection:                            IP40

Remarks

SAFETY APPROVAL & RATING:

Approved Rating

Mark

Reference No.

15A 125VAC T105/55

UL&CUL

E215677

 

VDE

 

10(8)A 250VAC  16A250VAC

CQC

CQC09002031458

 

NEMKO

 

 

SEMKO

 

 

FIMKO

 

 

DEMKO

 

 

CE

 

 

TUV

 

 

ENEC

 

 

EK

 

 

CB

 


PARTS LIST:

ITEM

NAME

MATERIAL

1

Housing

Nylon: Dupont

3

Actuator

Nylon: Dupont

4

Terminal

Brass H62 with silver plated

5

Lever

Copper T2 with silver plated and silver alloy contact

6

Spring

Steel

 

 

 

 

Returned plastic should not exceed 20%.

Applications

Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.
Electronic Equipment
Toys, Power tools, Car control panel etc.
Medical Equipment
Communication Equipment
Automation Equipment
Automotive Electronics
Instrumentation

Technical parameters

1.DETAIL SPECIFICATIONS:
Type:KAN-D3-6    
Construction category:D
Operation method:Rocker Action
Configuration:Single-Pole Single-Through (SPST)
Terminal form:#250 quick-connect Terminal
Mounting:Snap-In
Protection:IP40
1.1OPERATING CHARACTERISTICS

Characteristics

Units

Standards

Note

Actuating Force

N

3±1.5 Max

Original 3±1.5  .

Contact Force

N

0.4 Min

Original 0.4 Min

Electrical Clearance

mm

3 Min

Original 3 Min

Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
1.2.1Application This specification is applied to KAN Rocker Switch used for electronic equipment.
1.2.2 Operating temperature range -25℃ to +105℃
1.2.3Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows  
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.  
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications

NO.

Items

Test conditions

Criteria

1.4.1

Contact 

resistance

Shall be measured at 

12A 24VDC by voltage 

drop method after some 

operations without load.

Applied position: Between 

terminal and terminal  

30mΩ MAX

1.4.2

Insulation 

resistance

Test voltage:500VDC, 

measured after 1 min ±5s

Applied position: 1)Between 

terminal and terminal 

2)Between terminal and ground

100MΩ MIN

1.4.3

Voltage 

proof

Following test voltages shall 

be applied for 1 min.

(Cut-off  current:0.5mA)

1)Between terminal and 

terminal :2000VAC/min 

(50~60Hz)

2)Between terminal and 

ground: 2500VAC/min 

(50~60Hz)

No dielectric 

breakdown

shall occur

1.5. ENVIRONMENT RESISTANCE

NO.

Item

Test conditions

Criteria

1.5.1

Cold

After testing at -25±2℃ 

for 96 h, the switch shall 

be allowed to stand under 

normal room temperature 

and humidity condition for 

1h, and then measurement 

shall be made within 1 h. 

water drops shall be 

removed.

Contact 

resistance

(item 4.1): 

100mΩ MAX

Insulation 

resistance 

(item 4.2):

50MΩ MIN

Voltage proof:

 (item 4.3)

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Operating 

characteristic 

variety Within 

±10% of 

specified value .

No abnormalities 

shall be 

recognized in 

appearance and 

construction.

1.5.2

Dry heat

After testing at 105±2℃ for 

96 h, the switch shall be 

allowed to stand under 

normal room temperature 

and humidity condition for 

1h, and then measurement 

shall be made within 1 h.

1.5.3

Damp heat

After testing at 40±2℃ and

90-95%RH for 96 h, the 

switch shall be allowed to 

stand under normal room 

temperature and humidity 

condition for 1h, and then 

measurement shall be made 

within 1 h. water drops shall 

be removed.

1.5.4

Change of

temperature

After 20 cycles of following 

conditions the switch shall 

be allowed to stand under 

normal room temperature 

and humidity condition for 

1h, and then measurement 

shall be made within 1 h. 

water drops shall be 

removed.

1.5.5

Salt mist

Switch shall be checked 

after following lest.

1) Temperature: 35±2℃

2) Salt solution: 5±1% 

(solids by mass)

3) Duration: 24±1h

After test, salt deposit 

shall be removed in 

running water 

No remarkable 

corrosion shall 

be recognized 

in metal part

1.6. WELDING CHARACTERISTICS

 

1.6.1

 

Solder 

ability

Switch test under such conditions and 

inspect after. 

1)Variable temperature range :235±5℃;

2)Dip time:3±0.5s;

 

The area of dip 

tin should capture 

the 95% 

impregnated area

 

1.6.2

 

Resistance to 

soldering heat

 

The switch will be inspect under such 

conditions below

Temperature and impregnated time

Trial measure

temperature

(℃)

Time

(s)

Slot welding method

260±5

5±1

Soldering method

350±5

3±0.5

 

 

All of the appearance, 

motor functions, 

electrical properties 

are no abnormal.  

1.7. ENDURANCE

NO.

Item

Test condition

Criteria

1.7.1

Endurance

(According to

 UL61058)

10(10)250VAC

Switch shall be operated according to

 following sequence

(Test1~Test2)

 

Voltage

Current

Power 

factor

Operation

 rate

Number 

of 

operation

Test1

250V

12A

0.75-0.8

6-10

cycles/min

50cycles

Test2

250V

10A

0.75-0.8

6-10

cycles/min

6000

cycles

Voltage proof(Cut-off current:0.5mA)

1GPA 125/250VAC ;

Switch shall be operated 6,000 cycles at 15-20 cycles/min.

Test voltages shall be applied for 1 min

 

Insulation 

resistance

(item 4.2): 

30MΩ MIN

Voltage proof:

Terminal and 

ground:1000VAC

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Operating 

characteristic 

variety 

Within ±20% 

of specified 

value .

6000 cycles 

temperature 

rise:30℃ MAX;

10,000 cycles 

temperature 

rise:55℃ MAX;

 

No abnormalities 

shall be recognized 

in appearance and 

construction

1.7.2

Endurance

(According to 

EN61058-1

/IEC61058-1)

15(15) A 125VAC

Switch shall be operated 10,000 cycles at 15~20 cycles/min

Voltage proof(Cut-off current:0.5mA)

Test voltages shall be applied for 1 min.

 

Insulation 

resistance

(item 4.2): 

50MΩ MIN

Voltage proof:

Terminal and 

terminal:750VAC

Terminal and 

ground:1500

VAC

No dielectric 

breakdown 

shall occur.

Operating 

characteristic

(item 5.1):

Operating 

characteristic 

variety 

Within ±20%

of specified 

value .

Temperature 

rise:55℃ MAX

No abnormalities 

shall be 

recognized in 

appearance and 

construction

2.DRAWING & DIMENSION:

3. CIRCUIT DIAGRAM:

4. PACKING:

4.1

Packing material:

Plastic bag / 
Double-layers paper carton

4.2

Packing number:

100 pieces per bag 
10 bags per inner carton
2 inner cartons per shipping carton

Each shipping carton 2000 pieces

4.3

Weight:

Gross Weight:  13.5kg

Net Weight:   12.0kg 

4.4

Size:

31 x26 x27 CM /0.022CBM

Contact Us