條號NO.

項目 

Items

測試條件

Test conditions

標準

Criteria

2.2.1

接触电阻

Contact Resistance

500mΩ MAX

2.2.2

绝缘电阻

Insulation Resistance

测试相邻引脚之间,引脚与外壳之间的绝缘阻抗(DC 100V).

Measurement shall be made between adjacent terminals, between terminal and shell(DC 100V).

100MΩ MIN

2.2.3

耐压

Dielectric Withstand Voltage

输入一定电压(50-60Hz,电压值 AC 100V)1 分钟,漏电流为0.5mA,测试邻近端子间.

Apply certain voltage (50-60Hz,AC 500V) for 1 minute between adjacent contacts of the connector with 0.5mA leakage sensitivity.

沒有发烧介质击穿现象。

No arcing , break down and damaging insulation.

條號NO.

項目 

Items

測試條件

Test conditions

標準

Criteria

2.3.1

可焊性试验

Solder ability Test

端子顶部被浸入焊锡炉中，温度为230±5℃，时间3±0.5 秒.

The top of the terminals shall be dipped in the solder bath at 230±5℃ for 3±0.5 seconds.

引脚至少95%上锡.

Ninety-five percent of terminals shall be dipped.

2.3.2

寿命试验

Operation Life

开关在DC 30V 100mA的电阻回路中以约15-20次／分的速度连续被操作。

The switch is continuously operated in a DC 30V 100mA resistor circuit at a speed of approximately 15-20 times per minute.

寿命: 50,000 次

实验后：

接触电阻：1ΩMax

开关外观及结构无损坏。

Life test:100,000cycles

After test:

Contact resistance:1Ω Max

No abnormalities shall be recognized in appearance and construction.

2.3.4

振动Vibration

根据以下给定条件进行测试：

振动频率范围：10～55～10Hz；振幅（峰－峰）：1.5mm

振动方向：包括手柄行程方向在内的三个相互垂直的方 向；测试时间：每个方向2hours .

Measurement shall be made following the test set forth below:

1) Vibration frequency range: 10Hz to 55Hz to 10Hz; 2)  Amplitude: 1.5mm; 3) Direction of vibration: three mutually perpendicular direction including the direction of stem travel4)  Duration: Each 2hours.

机械性能、电气性能无异常.

There are no abnormalities in mechanical and electrical performance

2.3.5

抗冲击性Impact Resistance

以686縻m/s²（70g）的加速度、11ms作用时间，向包括操作方向在内的垂直6方向分别施加3次冲击试验

At 686 m/s ² Apply 3 impact tests in the vertical 6 directions, including the operating direction, with an acceleration of (70g) and an action time of 11ms

條號NO.

項目 

Items

測試條件

Test conditions

標準

Criteria

2.4.1

操 作 力

Operation Force

逐渐施力操作开关手柄，测量开关到达全部工作行程时所需的最大操作力度。

Operate the actuator of the switch and then increase press strength gradually, Measured maximum operation force while the travel of the switch is full.

30g±20g

2.4.2

端子强度Terminal Strength

在端子顶端向任一方向施加30gf静载荷1分钟，每一端子一次，端子弯曲无妨。

Apply a static load of 30gf in any direction at the top of the terminal for 1 minute, once per terminal, and the terminal bending is not harmful.

机械性能、电气性能无异常

No abnormalities in mechanical and electrical performance

2.4.3

操作部强度Operating Department Strength

各方向须经受住15秒100gf的静载荷

Each direction must withstand a static load of 100gf for 15 seconds

條號NO.

項目 

Items

測試條件

Test conditions

標準

Criteria

2.5.1

低溫Cold

在經受-20±2℃，96小時試驗之後，開關在常溫常濕條件下恢復1小時，然後在1小時內完成測量。要除去凝露。

After testing at -40±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.

接觸電阻：500mΩ MAX；

Contact resistance: 500mΩMAX;

絕緣電阻：100MΩ MIN；

Insulation resistance:100MΩ MIN

耐壓試驗：沒有發生介質擊穿現象；

Voltage proof: No dielectric breakdown shall occur.

動作特性：變化值在規定值的±10%以內；

Operating characteristic :

Operating characteristic variety Within ±10% of specified value .

外觀及結構無異常。

No abnormalities shall be recognized in appearance and construction.

2.5.2

高溫Dry heat

在經受70±2℃，96小時試驗之後，開關在常溫常濕條件下恢復1小時，然後在1小時內完成測量。

After testing at 85±2℃for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h.

2.5.3

恒定濕熱Damp heat

在經受溫度為 40±2℃ 相對濕度為 90-95%RH，96小時試驗之後, 開關在常溫常濕條件下恢復1小時，然後在1小時內完成測量。要除去凝露。

After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.