홈 /생산 /푸시 버튼 스위치 /일반 푸시 버튼 스위치
시리즈 :PS-12E05 series
This specification is applied to PS4-B202-60 Power Switch used for electronic equipment.
Operating temperature range: 0℃ to +85℃
Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
주위 온도 : 15 ~ 35 ℃
상대 습도 : 45 ~ 85 %
기압 : 86 ~ 106kPa (860 ~ 1060 mbar)
부품 목록:
|
NO. |
양 |
이름 |
자료 |
|
1 |
1 |
케이스 |
T375J(UL94V-0) |
|
2 |
1 |
Handspike |
PBT/PET(UL94V-0) |
|
3 |
1 |
덮개 |
Armor Plate, Nickel plated |
|
4 |
1 |
Spring holder |
1Cr18Ni9Ti |
|
5 |
1 |
Spring V |
QBe2 |
|
6 |
1 |
받침 |
H62, Silver plated |
|
7 |
1 |
Contact arm |
H62, Silver plated |
|
8 |
1 |
Moving contact |
AgNi10 / Cu |
|
9 |
1 |
Contact arm |
H62, Silver plated |
| 10 | 1 |
단말기 |
H62, Silver plated |
| 11 | 1 |
Fixed contact |
AgNi10 / Cu |
| 12 | 1 |
봄 |
Beryllium alloy Qbe2 |
| 13 | 1 |
Releasing spring |
72,Nickel plated |
반품 된 플라스틱은 20 %를 초과하지 않아야합니다.
응용
This specification is applied to PS-12E05 Power Switch used for electronic equipment.
Operating temperature range 0℃ to +85℃
Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
주위 온도 15 ~ 35 ℃
3 일반
3.1.1 Application This specification is applied to PS-22E05 Power Switch used for electronic equipment.
3.1.2 Operating temperature range 0℃ to +85℃
3.1.3 시험 조건 달리 명시되지 않는 한. 측정 및 테스트를위한 대기 조건은 다음과 같습니다.
주위 온도 : 15 ~ 35 ℃
상대 습도 : 45 ~ 85 %
기압 : 86 ~ 106kPa (860 ~ 1060 mbar)
판단에 의심이 생길 경우 시험은 다음 조건에서 수행되어야한다.
주위 온도 : 20 ± 2 ℃
상대 습도 : 60 ~ 70 %
기압 : 86 ~ 106kPa (860 ~ 1060 mbar)
3.2 외관 구성 및 치수
3.2.1 외관 스위치는 마무리가 양호해야하며 녹 균열이나 도금 결함이 없어야합니다.
3.2.2 구성 및 치수 개별 제품 도면을 참조하십시오.
Trip 2.5±0.5mm
Contact pressure ≥0.4N
The deviation in contact center no large than a quarter of contact diameter
Gap≥2.5mm
Drive type Press button kind, self-lock singe reset mechanical system
|
NO. |
항목 |
시험 조건 |
기준 |
|
3.3.1 |
접촉 저항 |
MEASURED AT 1 KHz SMALL CURRENT(100 mA OR LESS)
|
50mΩ MAX 50毫欧以下。 |
|
3.3.2 |
절연 저항 |
APPLY A VOLTAGE OF 500V DC SHALL BE APPLIED FOR 1 MIN AFTER WHICH MEASUREMENT BE MADE: (1) BETWEEN TERMINAL. (2) BETWEEN INDIVIDUAL TERMINAL AND FRAME.
|
100MΩ MIN
|
|
3.3.3 |
전압 증명 |
AC 500V rms(50~60Hz) FOR 1 MIN TRIP CURRENT: 0.5 mA 1)BETWEEN TERMINAL. 2)BETWEEN INDIVIDUAL TERMINAL AND FRAME.
|
WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC.
|
|
항목 |
설명 |
시험 조건 |
표준 시편 |
|
1 |
Terminal strength |
A STATIC LOAD OF 300 gf SHALL BE APPLIED TO THE TERMINAL FOR 15 SEC. IN ANY DIRECTION.
|
THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY.ELECTRICAL AND MECHANICALCHARACTERISTICS SHALL BE SATISFIED. |
|
2 |
DISPLACEMENT OF ACTUATOR （KNOB）
|
A STATIC LOAD OF 10N（1Kgf）SHALL BE APPLIED TO THE TOP OF THE ACTUATOR(KNOB) AND THEN DISPLACEMENT SHALL BE MEASURED TO THE DIRECTION OF THE ARROW. |
THE LEVER SHALL HAVE NO ANFUNCTION IS NORMALLY.
|
|
3 |
LIFE TEST
|
WITHOUT LOAD: AN ACTUATOR SHALL BE SUBJECT TO 10,000 CYCLES AT A SPEED OF 15~18 CYCLES FOR 1 MIN.
|
1)CONTACT RESISTANCE 100 mΩ MAX 2）INSULATION RESISTANCE 50MΩ MIN. 3）WITHSTAND VOLTAGE AC 500V, 1 MINUTE. （4）OPERATING FORCE ±30% INITIAL VALUE. （5）WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC.
|
|
NO. |
항목 |
시험 조건 |
기준 |
|
3.5.1 |
습기
|
THE JACK SHALL BE STORED AT A TEMPERATURE OF 40±2 °C AND A HUMIDITY OF 90% TO 95% FOR 96 Hr . THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES.
|
|
|
3.5.2 |
표준 ATMOSPHERIC 정황
|
UNLESS OTHERWISE SPECIFIED. THE STANDARD RANGE OF ATMOSPHERIC CONDITIONS FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS: (1) AMBIENT TEMPERATURE : 5 °C TO 35 °C (2) RELATIVE HUMIDITY: 45% TO 85% (3) AIR PRESSURE 86Kpa TO 106Kpa
|
|
|
3.5.3 |
PRACTICAL 온도 RANK
|
-16 °C ~ +60°C
|
|
|
3.5.4 |
STORAGE METHOD
|
(1) IF DON'T USE THE PRODUCT IMMEDIATELY,STORE IT AS DELIVERED IN THE FOLLOWING ENVIRONMENT: WITH NEITHER DIRECT SUNSHINE NOR CORROSIVE GAS AND IN NORMAL TEMPERATURES. HOWEVER, IT IS RECOMMENDED THAT YOU SHOULD USE IT AS SOON AS POSSIBLE BEFORE SIX MONTHS PASS. |
|
|
(2) AFTER BREAK THE SEAL，IT SHOULD PUT THE REMAINING IN A PLASTIC BAG TO SEPARATE IT FROM THE OUTSIDE AND STORE IN THE SAME ENVIRONMENT MENTIONED ABOVE. YOU SHOULD USE IT UP AS SOON AS POSSIBLE. |
|||
|
(3) DO NOT STACK TOO MANY SWITCHES FOR STRAFE.
|
|||
|
3.6.1 |
솔더 능력 |
THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 235±5 °C FOR 3±0.5 SECONDS.
|
The area of dip tin should capture the 75% impregnated area |
|||||||||
|
3.6.2 |
납땜 열에 대한 저항 |
The switch will be inspect under such conditions below 온도 및 함침 시간
(2) TMMERSION DEPTH: IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6 mm.
|
WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OFTERMINALS MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
|
|||||||||
|
3.6.3 |
HEAT TEST
|
THE JACK SHALL BE STORED AT A TEMPERATURE OF 85±2 °C FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE.
|
||||||||||
|
3.6.4 |
COLD TEST
|
THE JACK SHALL BE STORED AT A TEMPERATURE OF -10±2 °C FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE.
|
4. 도면 및 치수 :
저작권 2019 게시자 : Switech Electronics Co., Ltd
EN 
ES
AR
NL
JA
KO
FR
RU
