+86-0512-62885849

EN
All Categories

Home /Products /Push Button Switch /Metal Push Button Switch

  • /img/mw19-a0f1l6220-b1tb-anti-vandal-ip67-metal-16a-push-button-switch.jpg

MW19-A0F1L6220-B1TB anti-vandal IP67 metal 16A push button switch

Series:MW19 series

Quick Detail:

Type: MW19-A0F1L6220-B1TB
Construction category: D type
Operation method: Push button switch
Configuration: Single-Pole Single -Throw (SPST)
Terminal form: Solder Terminal
Protection: IP67
Ratings: 16A 250VAC,125VAC      
Withstand voltage: 1000VAC,1Min

  • Remarks
  • Applications
  • Technical parameters
Remarks

SAFETY APPROVAL & RATING:

Approved Rating

Mark

Reference No.

16A 250VAC

UL&CUL

 

 

VDE

 

 

CQC

 


 PARTS LIST: 

Note: Returned plastic should not exceed 20%.

NO.

quantity

Items

Material

1

1

Bushings

Stainless steel

2

1

Base

PBT; PC; PA6T

3

 1

Actuator

PC; Stainless steel

4

1

Inner assembly

POM/PA66

5

1

Spring 

Steel

6 1

Sealing

Silicone

7 1

O-ring

Silicone

8 1

Terminal

Brass silver plated

9 1

Hex nut

Nickel plated brass

Applications

Enormous remote
controller and portable remote controller

Instrumentation
Medical equipment

Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls

Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls

Public building, Home security, Business building, Industrial equipment…etc.

Technical parameters


3.1   General
3.1.1  Application        This specification is applied to KAN-J4 Power Switch used for electronic equipment.
3.1.2 Operating temperature range       -25℃ to +85℃                                
3.1.3  Test conditions           Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:            15~35℃
Relative humidity:            45~85%
Air pressure:                86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:            20±2℃
Relative humidity:            60~70%
Air pressure:                86~106kPa (860~1060 mbar)
3.2Appearance construction and dimensions

3.2.1 Appearance                Switch shall have good finishing, and no rust crack or plating failures.
3.2.2Construction and dimensions       Refer to individual product drawing.

3.3.  Electrical Characteristics 

NO.

Items

Test conditions

3.3.1

Contact resistance

The contact resistance should be 50mΩ(Max).

3.3.2

Insulation resistance

It is measured with 500V DC 1minute should be 1000MΩ(Min).

3.3.3

Dielectric strength

AC 1000V,1min.(before endurance test)

 AC 2000V,1min.(after endurance test)

3.4 Mechanical Characteristics 

Item

Description

Test Conditions

1

Operating Force

3.15±1.5N

2

Operating Life

The mechanical life all of 50 000 cycles

3

Contact Spacing

Min. 3.0mm (IEC61058)

3.5Durability 

 NO.

Item

Test condition

Criteria

3.5.1

Endurance

(According to

 UL61058)

16A 250VAC 

Switch shall be operated according to following sequence

(Test1~Test2)

 

Voltage

Current

Power factor

Operation rate

Number of operation

Test1

250VAC

16A 

0.75-0.8

6-10

cycles/min

50cycles

Test2

250VAC

16A 

0.75-0.8

6-10

cycles/min

6000cycles

Voltage proof(Cut-off current:0.5mA)

16A 250VAC 

Switch shall be operated 50,000 cycles at 15-20 cycles/min.

Test voltages shall be applied for 1 min

Insulation resistance(item 4.2):

50MΩ MIN

Voltage proof:

Terminal and ground:1000VAC

No dielectric breakdown shall occur.

Operating characteristic (item 5.1):

Operating characteristic variety

Within ±20% of specifiedvalue .

6000 cycles temperature rise:45MAX;

10,000 cycles temperature rise:55 MAX;

 

No abnormalities shall be recognized in appearance and construction

3.5.2

Endurance

(According to EN61058-1

/IEC61058-1)

16A 250VAC 

Switch shall be operated 50,000 cycles at 15~20 cycles/min

Voltage proof(Cut-off current:0.5mA)

Test voltages shall be applied for 1 min.

Insulation resistance(item 4.2):

50MΩ MIN

Voltage proof:

Terminal and terminal:750VAC

Terminal and ground:1500VAC

No dielectric breakdown shall occur.

Operating characteristic (item 5.1):

Operating characteristic variety

Within ±20% of specifiedvalue .

Temperature rise:55 MAX

No abnormalities shall be recognized in appearance and construction


3.6. SOLDERING
Solder ability and Resistance to sold heat according to IEC 68-2-20

4.DRAWING & DIMENSION:


Contact Us