EN 
ES
AR
NL
JA
KO
FR
RU
PS585-A2P 5.8*5.8mm 2 pins momentary push button switch
Series:PS585 series
Quick Detail:
Type: PS585-A2P
Construction category: off-(on)
Operation method: Push button switch
Configuration: Double-Pole Double-Through (DPDT)
Terminal form: PCB Terminal
Protection: IP40
- Remarks
- Applications
- Technical parameters
Remarks
-
PARTS LIST:
NO.
quantity
Items
Material
1
1
guide core
PA66
2
1
cover
PA66
3 1 case
PPA
4 1 spring
Stainless steel
5 2 contact spring
Compound silver
6 2 terminal
Brass plating silver
Note: Returned plastic should not exceed 20%.
Applications
Widely used in home appliance, electronic equipment, automatic machine, communication equipment, car electron, apparatus and instrument, electric motion tool etc.
Rice cooker
Slow cooker
Electric Heating Faucet
Shredder
Computer mouse
Electromagnetic lock
Baby chair
CNC machine tools
Power generator
Test equipment
Elevator
Power tools
Air conditioner
Water heater control panel
Bathroom products
Vacuum cleaner
Kitchen products
Gas valve
Range hood machine
Microwave oven
Pass-through machine
Technical parameters
3.DETAIL SPECIFICATIONS:
Type: PS585-A2P
Construction category: off-(on)
Operation method: Push button switch
Configuration: Double-Pole Double-Through (DPDT)
Terminal form: PCB Terminal
Protection: IP40
3.1 General
3.1.1Application This specification is applied to PS585 Power Switch used for electronic equipment.
3.1.2 Operating temperature range -40℃ to +80℃
3.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
3.2Appearance construction and dimensions
3.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
3.2.2Construction and dimensions Refer to individual product drawing.
3.3. Electrical Characteristics
|
NO. |
Item |
Test conditions |
Criteria |
|
3.3.1 |
Contact resistance |
Applying a static load of 2 times operating force to the center of the stem, measurements shall be made by 5V DC 10mA or more than IKHZ AC small-current contact resistance meter. |
200mΩ MAX |
|
3.3.2 |
Insulation Resistance |
Measurement shall be made following application of 100V DC potential, across terminals, and across terminals and cover, for one minte. |
100MΩ MIN |
|
3.3.3 |
Voltage proof |
250VAC (50HZ或60HZ) /min 250V AC(50hz or 60HZ)shall be applied across terminals, for one minute. |
No dielectric breakdown shall occur |
1.4 Environment Resistance
|
NO. |
Items |
Test conditions |
Criteria |
|
1.4.1 |
Cold |
After testing at -40±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. |
500mΩ MAX； Contact resistance: 500mΩMAX;
|
|
1.4.2 |
Dry heat |
After testing at 80±2℃for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. |
|
|
1.4.3 |
Damp heat |
After testing at 60±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. |
1.5Durability
|
NO. |
Item |
Test condition |
Criteria |
|
1.5.1 |
Operation life |
Measurement shall be made following the test set forth below: DC 30V, 100mA resistance load; Rate of operation:60-120 times/min.; OF：1.5OF Average fault-free life： 10,000 cycles |
Contact resistance:≤200mΩ Contact bounce: ≤10ms Operating Force: initial value±30% |
|
1.5.2 |
OF |
The switch is placed perpendicular to the direction of the operation, gradually force in key top center of switch, measure maximum intensity when it conducted required. |
250±50gf |
| 1.5.2 | OT | Switch at the vertical operating orientation placement, with a force equal to 2 times according to the static load applied on the switch button the top center, measure the top moving distance. | 2.0±0.2mm |
1.6. Welding Performance:
|
1.6.1 |
Solder ability |
Switch test under such conditions and inspect after. 1）Variable temperature range ：245±5℃； 2）Dip time：2±0.5s； |
The area of dip tin should capture the 90% impregnated area |
|||||||||
|
1.6.2 |
Resistance to soldering heat |
The switch will be inspect under such conditions below temperature and impregnated time
|
All of the appearance, motor functions, electrical properties are no abnormal. |
2. DRAWING & DIMENSION:
3. PACKING:
|
3.1 |
Packing material: |
Plastic box / |
|
3.2 |
Packing number: |
500 pieces per bag |
|
3.3 |
Weight: |
Gross Weight: 5.35 kg Net Weight: 5.05 kg |
|
3.4 |
Size: |
57.0 x 26.0 x 32.0 CM / 0.045CBM |