R13-11SW2 paddle switch SPDT 3pins ON-OFF 187 quick-connect terminal rocker switch for dust catcher

Remarks

Applications

Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.
Electronic Equipment
Toys, Power tools, Car control panel etc.
Medical Equipment
Communication Equipment
Automation Equipment
Automotive Electronics
Instrumentation

Technical parameters

1.DETAIL SPECIFICATIONS:
Type:                                  R13-11SW12
Construction category:      D
Operation method:            Rocker Action
Configuration:                    Single-Pole Single-Through (SPST)
Terminal form:                    #187 quick-connect Terminal
Mounting:                           Snap-In
Protection:                          IP40
1.1OPERATING CHARACTERISTICS

Characteristics	Units	Standards	Note
Actuating Force	N	4±2 Max	Original 4±2
Contact Force	N	0.4 Min	Original 0.4 Min
Electrical Clearance	mm	3 Min	Original 3 Min

Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
3.2.1Application                    This specification is applied toR13 Rocker Switch used for electronic equipment.
3.2.2 Operating temperature range 0~85℃
3.2.3Test conditions              Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:          15~35℃
Relative humidity:                 45~85%
Air pressure:                         86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:          20±2℃
Relative humidity:                60~70%
Air pressure:                       86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
3.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
3.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications

NO.	Items	Test conditions	Criteria
1.4.1	Contact resistance	Shall be measured at 50VAC by voltage drop method after some operations without load. Applied position: Between terminal and terminal	30mΩ MAX
1.4.2	Insulation resistance	Test voltage:500VDC, measured after 1 min ±5s Applied position: 1)Between terminal and terminal 2)Between terminal and ground	100MΩ MIN
1.4.3	Voltage proof	Following test voltages shall be applied for 1 min. (Cut-off current:0.5mA) 1)Between terminal and terminal :1250VAC/min (50~60Hz)	No dielectric breakdown shall occur

1.5. ENVIRONMENT RESISTANCE

NO.	Item	Test conditions	Criteria
1.5.1	Cold	After testing at -25±2℃ for 96 h, the switch shall be llowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.	Contact resistance(item 4.1): 100mΩ MAX Insulation resistance (item 4.2): 50MΩ MIN Voltage proof: (item 4.3) No dielectric breakdown shall occur. Operating characteristic (item 5.1): Operating characteristic variety Within ±10% of specified value . No abnormalities shall be recognized in appearance and construction.
1.5.2	Dry heat	After testing at 105±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h.
1.5.3	Damp heat	After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
1.5.4	Change of temperature	After 20 cycles of following conditions the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
1.5.5	Salt mist	Switch shall be checked after following lest. 1) Temperature: 35±2℃ 2) Salt solution: 5±1% (solids by mass) 3) Duration: 24±1h After test, salt deposit shall be removed in running water	No remarkable corrosion shall be recognized in metal part

1.6. WELDING CHARACTERISTICS

1.6.1

Solder ability

Switch test under such conditions

and inspect after.

1）Variable temperature range ：235±5℃；

2）Dip time：3±0.5s；

The area of

dip tin should

capture the

95% impregnated

area

1.6.2

Resistance to

soldering heat

The switch will be inspect under such

conditions below

Temperature and impregnated time

Trial measure

temperature

（℃）

Time

（s）

Slot welding method

260±5

5±1

Soldering method

350±5

3±0.5

All of the

appearance,

motor

functions,

electrical

properties

are no

abnormal.

1.7. ENDURANCE

NO.

Item

Test condition

Criteria

1.7.1

Endurance

(According to

UL61058)

12A 125VAC

Switch shall be operated according to

following sequence

(Test1~Test2)

Voltage

Current

Power

factor

Operation

rate

Number

of operation

Test1

125V

12A

0.75-0.8

6-10

cycles/min

50cycles

Test2

125V

12A

0.75-0.8

6-10

cycles/min

6000

cycles

Voltage proof(Cut-off current:0.5mA)

1GPA 125/250VAC ;

Switch shall be operated 6,000 cycles at 15-20 cycles/min.

Test voltages shall be applied for 1 min

Insulation

resistance

(item 4.2):

30MΩ MIN

Voltage proof:

Terminal and

ground:1000VAC

No dielectric

breakdown

shall occur.

Operating

characteristic

(item 5.1):

Operating

characteristic

variety

Within ±20%

of specified

value .

6000 cycles

temperature

rise:30℃ MAX;

10,000 cycles

temperature

rise:55℃ MAX;

No abnormalities

shall be recognized

in appearance and

construction

1.7.2

Endurance

(According to

EN61058-1

/IEC61058-1)

12 (8) A 250VAC

Switch shall be operated 10,000 cycles at

15~20 cycles/min

Voltage proof(Cut-off current:0.5mA)

Test voltages shall be applied for 1 min.

Insulation

resistance

(item 4.2):

50MΩ MIN

Voltage proof:

Terminal and

terminal:750VAC

Terminal and

ground:1500VAC

No dielectric

breakdown

shall occur.

Operating

characteristic

(item 5.1):

Operating

characteristic

variety

Within ±20%

of specified

value .

Temperature

rise:55℃ MAX

No abnormalities

shall be

recognized in

appearance

and construction

2. DRAWING & DIMENSION:

3. CIRCUIT DIAGRAM：

4. PACKING:

4.1	Packing material:	Plastic bag / Double-layers paper carton
4.2	Packing number:	200 pieces per bag 10 bags per inner carton 3 inner cartons per shipping carton 1 shipping carton 6000 pieces
4.3	Weight:	Gross Weight: 26 kg Net Weight: 24.5 kg
4.4	Size:	572732CM /0.049248CBM

Contact Us

Approved Rating	Mark	Reference No.
10(6)A 125/250VAC	UL&CUL	E256173
12(8)A 250VAC	VDE	0630-1
12(8)A 250VAC	CQC	CQC09002039559
	NEMKO
	SEMKO
	FIMKO
	DEMKO
	CE
	TUV
	ENEC
	EK
	CB

ITEM	NAME	MATERIAL
1	Button	Plastic
2	Base	Plastic
3	Terminal	Brass alloy H65,Silver Plated
4	Plate moving	Brass alloy H65,Silver Plated
5	Contact	Silver-Cadmium Oxide alloy
6	Contact	Silver-Cadmium Oxide alloy
7	Spring	Manganese Steel
8	Steel Ball	Stainless Steel

All Categories

Products

Micro Switch

Rocker Switch

Tactile Switch

Push Button Switch

Slide Switch

Toggle Switch

Dip Switch

Type-C

Rotary

Potentiometer

Socket

Circuit Breakers

The encoder

Detect Switch

Reset Switch

Pressure Switch

R13-11SW2 paddle switch SPDT 3pins ON-OFF 187 quick-connect terminal rocker switch for dust catcher

Quick Detail:

Remarks

Applications

Technical parameters

Products

Contact Us

E-Mail Subscription