R-SW220C5W-LBR5-151NC paddle switch 6 pins ON-OFF DPDT red light momentary rocker switch used for elevator

Approved Rating

Mark

Reference No.

15A 125VAC 60HZ

UL&CUL

E300970

VDE

CQC

NEMKO

SEMKO

FIMKO

DEMKO

CE

TUV

ENEC

EK

CB

ITEM

NAME

MATERIAL

1

Base

Plastic

2

Button

Plastic

3

Lamp holder

Nylon 66 94V-0

4

Contact

Silver zinc alloy

5

Contact

Silver zinc alloy

6

Spring

Jean steel wire

7

resistance

resistance

8

Light

Neon lamp-Red

9

Terminal

Copper tin plating

10

Terminal

Copper tin plating

11

Moving piece

Copper plating silver

12

White oil

White oil

13

Ink

Ink

R series switch operation force

Single-Pole

Double-Pole 

Function

Operation force

Function

Operation force

1

ON-OFF

400±200 gram

1

ON-OFF

600±200 gram

2

ON-ON

400±200 gram

2

ON-ON

600±200 gram

3

ON-OFF-ON

400±200 gram

3

ON-OFF-ON

600±200 gram

4

(ON)-OFF

1000±200 gram

4

(ON)-OFF

1000±200 gram

5

(ON)-ON

1000±200 gram

5

(ON)-ON

1000±200 gram

6

(ON)-OFF-(ON)

1100±300 gram

6

(ON)-OFF-(ON)

1100±300 gram

7

(ON)-OFF-ON

(900±300)-200±100 gram

7

(ON)-OFF-ON

(1300±300)-700±200 gram

(   ):Momentary

NO.

Items

Test conditions

Criteria

3.4.1

Contact resistance

Measure by micro-ohm meter at DC. 5V 1A

Applied position: Between terminal and terminal  

20mΩ MAX

3.4.2

Insulation resistance

Measure with DC. 500V applied between terminals of open contacts and betweenterminals of opposite polarity.

100MΩ MIN

3.4.3

Voltage proof

A switch shall withstand for 1 minute without breakdown or arc in a potential applied between terminals of open contacts and between terminals of opposite polarity, and between terminals and frame as following:

1000 volts for a switch rated 250VAC or less. (UL)

1500 volts for a switch rated 250VAC or less. (IEC)

No dielectric breakdown

shall occur

The test should be taken after load test with its rated current and voltage, and measured by the following standards.

3.5.1. The temperature rise after the load test shall not be more than 30℃. (UL)

3.5.2. The temperature rising shall not be more than 55℃. (IEC)

A static force of 5 pound (2.27kg) being applied in one direction on the tip of the terminal for 1 minute. The terminal may be deformed, but shall not sustain any trouble as deviation and breaking of terminal and breaking of insulation material.

The force required to insert and withdraw the tab and connector of a quick-connect terminal shall comply with the values as follows:

1.7.1 First insertion: 18 pounds, max. Individual.

1.7.2 First withdrawal: 20 pounds, max. Individual. 3 pounds, min individual.

1.7.3 Sixth withdrawal: 2 pounds, min. individual.

1.8.1

S.M.T. dipping:

The temperature of soldering should be 260±5℃within 5±1 seconds of dipping duration, and more than 75% of the terminal shall be covered by solder.

After the soldering, the switch shall not have any

deformations or fail to function

1.8.2

Handwork soldering

The temperature of soldering should be 350±5℃when applied with a 60W iron head, and should abide by the following rules:

1) The soldering iron shall not be pressed to terminal when soldering, but only slightly touch the surface of the terminal

2) Soldering time should be controlled within 3 seconds, at most not exceeding 5 seconds.

3) After the soldering, the switch shall not have any deformations or fail to function.

No dielectric breakdown

shall occur

NO. 

Items 

Test conditions 

Criteria 

1.9.1

Mechanical life test

The switch applied without electric load, should operate at least 50,000 times, without mechanical failure.

1.9.2

Load test

1.9.3

Endurance test

NO.

Item

Test conditions

Criteria

1.10.1

Cold

Put the switch at -40±2℃for 96 hours and then take it out one hour measuring it at normal temperature and humidity surrounding within one hour after clean off water vapor.

Contact resistance: Lower 20m.

Insulation resistance: Over 100M.

Dielectric voltages withstand: The same as Point No. 3.4.3

1.10.2

Dry heat

Put the switch at 85±2℃for 96 hours and then take it out one hour, measuring it at normal temperature and humidity surrounding within one hour after clean off water vapor.

1.10.3

Humidity endurance

Put the switch at 40±2℃relative humidity 90 to 95% for 96 hours and then take it out one hour, measuring it at normal temperature and humidity surrounding within one hour after clean off water vapor.

4.1

Packing material:

Plastic bag / 
Double-layers paper carton

4.2

Packing number:

200 pieces per bag 
8 bags per shipping carton
Each shipping carton 1600 pieces

4.3

Weight:

Gross Weight:  8 kg

Net Weight:   7 kg

4.4

Size:

40*30*23CM /0.0276㎡