EN 
ES
AR
NL
JA
KO
FR
RU
SW05152A SERIES 04-60PINS 0.50mm PITCH 1.5H Easy on FPC CONNECTOR
Series:SW05152A
Rating:DC50V 0.5A
Quick Detail:
- Remarks
- Applications
- Technical parameters
Remarks
Applications
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
Technical parameters
2. 产品规格DETAIL SPECIFICATIONS:
2.1 一般特性 General
2.1.1 適用範圍Application 本规范适用于 0.5mm 间距 1.5 高度掀盖式 FPC 系列产品.
This specification covers the 0.5PH 1.5H Easy on FPC series.
2.1.2 工作溫度範圍Operating temperature range -25℃ ～ +85℃
2.1.3 存储溫度範圍Storage temperature range -25℃ ～ +85℃
2.1.4 測試條件Test conditions 除非另有規定，測量是和試驗的環境條件如下：
Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows:
環境溫度：Ambient temperature: 15~35℃
相對濕度：Relative humidity: 25~85% 大氣壓：Air pressure: 86~106kPa (860~1060 mbar)
在判定中如果發生疑問，則遵循以下仲裁條件：
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
環境溫度：Ambient temperature: 20±2℃
相對濕度：Relative humidity: 60~70%
大氣壓：Air pressure: 86~106kPa (860~1060 mbar)
2.2外觀、結構和尺寸 Appearance construction and dimensions
2.2.1 外觀 開關外觀完好，無銹蝕、裂紋和鍍層缺陷。
Appearance Switch shall have good finishing, and no rust crack or plating failures.
2.2.2結構和尺寸 參見相應的產品圖樣
Construction and dimensions Refer to individual product drawing.
2.3. 電氣性能ELECTRICAL SPECIFICATION
|
NO. |
Items |
Test conditions |
Criteria |
|
2.3.1 |
Contact Resistance 接触电阻 |
Mate applicable FPC and measure by dry circuit 20mV Max,10mA （将样品与 FPC 连接，测试电压 20mV，限电流 10mA 进行阻抗测试）
|
Max 50 Ohm 最大50 Ohm |
|
2.3.2 |
Insulation Resistance 绝缘电阻 |
[500]VDC for 1 minute Test between adjacent circuits of unmated connector.（将样品与 FPC 连接， 提供相邻端子间测试电压 500VDC 进行绝缘阻抗测试）
|
Min 500 M Ohm 最小500 M Ohm |
|
2.3.3 |
Dielectric Breakdown voltage 耐电压强度 |
[500]VAC for 1 minute Test between adjacent circuits of unmated connector.（将样品与 FPC 连接， 相邻端子间可以承受 500VAC 1 分钟） |
No breakdown insulation 没有绝缘破损异常 |
2.4.机械特性MECHANICAL CHARACTERISTIC:
|
ITEM 项目 |
TEST DESCRIPTION 测试描述 |
TEST CONDITIONS 测试条件 |
SPECIFICATION 说明 |
|
2.4.1 |
Contact/Peg Retention Force 保持力
|
Apply axial pull out force at the rate of [25.4±3]mm/min on the terminal assembled in the housing. （端子与 PEG 插进主体水平方向拔出力量）
|
0.150kgf Min. （0.150kgf 最小）
|
|
2.4.2 |
FPC/FFC Retention Force FPC/FFC保持力
|
0.030kgf/Pin Min.(PIN>＝13) 0.040kgf/Pin Min.(PIN<13) （片数大于等于 13PIN 时 FFC/FPC 每 PIN 保 持 力 0.030kg 以上，片数小于 13PIN 时 FFC/FPC 每 PIN 保持力 0.040kg 以上.）
|
Operation Speed:[25.4±3] mm/min Measure the force required to unmated connector. （将盖子盖上，与 FPC 连接后以操作速度每分 钟 25.4±3mm 进行 FPC 保持力测试）
|
|
2.4.3 |
Durability 耐久性
|
Operation Speed: (10) cycle-max./ min Durability Cycles：20 Cycles 操作速度：10 次最大每分钟 耐久次数：20 次
|
Contact Resistance： 50m Ohm Max 接触阻抗：50m Ohm 最大
|
|
2.4.4 |
Vibration 振动试验
|
Amplitude：1.52m;Frequency;10~55~10HZ; Vibration time:2 hours for 3 axis total 6 hours. （振幅：1.52mm：振动频率：10~55~10HZ； 振动时间：X、Y、Z 轴各 2 小时）
|
Contact Resistance ：50mOhm Max Discontinuity（断电时间） ：1u sec. Max. Appearance no damage 外观无破坏
|
|
2.4.5 |
Mechanical Shock （冲击试验）
|
The connectors shall be soldered on the P.C. board. /Acceleration：50G. Time: 11ms.(half sine wave). Cycle: 3 cycle for 3 axis total 9 cycle. （FPC 焊接于 PC 板上，/加速度：50G.） （冲击作用时间：11ms.） [冲击次数：X、Y、Z 轴各 3 次（共 9 次）]
|
Contact Resistance ：50mOhm Max Discontinuity（断电时间） ：1u sec. Max. Appearance no damage 外观无破坏
|
|
2.4.6 |
Temperature Rising （温升）
|
Mate applicable FPC and measure the temperature rise of contact when the maximum AC mated current is.（量测通过 FPC 最大容许电流时， 样品接触之温升）
|
Temperature Rising (温升)：30℃ Max
|
2.5.耐環境性 Environment Resistance：
|
ITEM 项目 |
TEST DESCRIPTION 测试描述 |
TEST CONDITIONS 测试条件 |
SPECIFICATION 说明 |
|
2.5.1 |
Thermal Shock （热冲击试验）
|
Temperature range form -55℃ to +85℃ .Start from -55 ℃,after 30 min. Change to +85;℃chang time is no more than 30 seconds. Total 5 cycles. 温度变化范围：-55℃~+85℃；从-55℃开始， 30 分钟换到+85℃：转换时间不超过 30 秒：共 5 个循环。
|
接觸電阻：50 m Ohm MAX； Contact resistance: 50 m Ohm MAX;
絕緣電阻：500 m Ohm MIN； Insulation resistance ): 500 m Ohm MIN
外觀及結構無異常。 No abnormalities shall be recognized in appearance and construction.
|
|
2.5.2 |
Humidity Resistance 防潮强度
|
Switch for testing being kept in the conditions at 40±2℃ in temperature and 90~95% RH for 250 hours,and in a normal ambient condition for one hour,then measured within one hour. 放置40±2℃试验的相对湿度为90~95%环境中测试250小时后，再将其放置正常环境1小时后再测定。 |
|
|
2.5.3
|
Temperature Life 恒温恒室试验 |
Mated, Connector 85℃, 250 hours |
|
|
2.5.4 |
Salt-Spray Test 盐雾试验
|
The sample is allowed to stand the test chamber controlled to 35±2℃,in temperature and 5±1％ (Weight ratio) salt-water concentration for 24±1 hour and is subjected to test. Then,salt deposits attached to the sample are washed away with water. 样品经受在试验室控制温度在35±2℃,在高温和5±1％(重量比)盐水浓度为24±1小时,并因此而受的试验.然后,把实验品上的盐层用水冲冼 |
|
|
2.5.5 |
Solder Ability 焊接能力 |
Soldering temperature:245±5℃ Immersing time: 3±0.5 second 焊接温度：245±5℃ 焊接时间：3±0.5 second |
More than 95% of the part immersed can be covered with solder。 焊锡面积超过95% |
|
Reflow soldering（回流焊）: Pre Heat:150~180℃,90±30sec. Heat：230℃ Min.,30±10sec Peak Temp.:260+0/-5℃, 10sec. Or less Duration：2 cycles
|
|||
3. 图纸DRAWING:
