TS12I-072C-U-G15.3 12x12mm SMD Blue LED Pushbutton Switch

Remarks

Applications

1.Audio Products:MP3,MP4,DVD. Audio;
2.Digital Products: digital camera, digital video and so on;
3.Remote Control: the remote control of automobile domestic security products;
4.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
5.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;
6.Security Products: visual interphone, monitor and so on;
7.Toys: electric toys and so on;
8.Computer Products: PC camera and so on;
9.Exercises Machines: treadmills, massage armchair and so on;
10.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
11.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
12.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
13.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.

Technical parameters

2.1 General
2.1.1 Application This specification is applied to TACT Switch used for electronic equipment.
2.1.2 Operating temperature range -15℃ ～ +60℃
2.1.3 Storage temperature -25℃ ～ +70℃
2.1.4 Test conditions
Ambient temperature 5~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
If any doubt arise from the judgment, tests shall be conducted at the following conditions.
Ambient temperature： 20±2℃
Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)
2.2 Appearance construction and dimensions
2.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
2.2.2 Construction and dimensions   Refer to individual product drawing.

2.3. ELECTRICAL SPECIFICATION

NO.	Items	Test conditions	Requirements
2.3.1	Contact resistance	Applying a static load of 2 times operating force to the center of the stem, measurements shall be made by 5V DC 10mA or more than 1KHZ AC small-current contact resistance meter.	50mΩ MAX
2.3.2	Insulation resistance	Measurement shall be made following application of 100V DC potential, across terminals, and across terminals and cover, for one minute.	100MΩ MIN
2.3.3	Dielectric voltage proof	250V AC (50HZ or 60HZ) shall be applied across terminals, for one minute.	No dielectric breakdown shall occur.
2.3.4	Contact bounce	Lightly striking the center of the stem at a rate encountered in normal use (2 to 3 times per second), and bounce shall be tested at “ON” and “OFF”	ON-5msec.max OFF-8msec.max

2.4. ENVIRONMENT RESISTANCE:

NO.	Items	Test conditions	Requirements
2.4.1	Resistance to low temperature	Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1 h. Before measurements are made: 1)Temperature:-25±3℃ 2)Time: 16h	Contact resistance: 200mΩ MAX Insulation resistance: 50MΩ MIN
2.4.2	Heat resistance	Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1h before measurements are made: 1)Temperature:70±2℃ 2)Time: 72h
2.4.3	Moisture resistance	Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1h before measurements are made: 1)Temperature: 60±2℃ 2)Relative humidity: 90 to 95% 3)Time:96h	Voltage proof: No dielectric breakdown shall occur. Operating characteristic variety Within ±10% of specified value .
2.4.4	Change of temperature	After 5 cycles of following conditions, the sample shall be allowed to stand under normal temperature and humidity conditions for 1h and measurements shall be made. During the test waterdrops shall be removed.
2.4.5	Sulfuration resistance	Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1h before measurements are made: 1)H2S gas concentrations: 3ppm±1ppm; 2)Time:8h;3)Temperature: 40±2℃(90~95%RH)
2.4.6	Salt mist	The switch shall be checked after following test: 1)Temperature: 35℃±2℃ 2)Salt solution : 5±1%(solids by mass) 3)Time: 4±1 hour After test, salt deposit shall be removed by running water.	No remarkable corrosion shal be recognized in metal part.

2.5. WELDING PERFORMANCE

2.5.1

Solderability

Switch test under such

conditions and inspect after.

1)Variable temperature range ：235±5℃；

2)Dip time：2±0.5s；

Except for the edge,

the coating

should cover a

minimum 90%

2.5.2

Resistance heat

soldering

The switch will be inspect under

such conditions below

Trial measure

Temperature(℃)

Time(s)

Slot welding

method

260±5

5±1

Soldering method

350±5

3±0.5

There shall be no

sign of damage

mechanically and

electrically.

2.6. DURABILITY

2.6.1	Operation life	Measurement shall be made following the test set forth below: DC 12V, 50 mA resistance load; Rate of operation:120 times/min; Operating Force:1.5 times OF; Average fault-free life: 1,000,000 cycles	Contact resistance: ≤200mΩ Contact bounce: ≤10ms Operating Force: initial value±30%
2.6.2	Vibration	Measurement shall be made following the test set forth below: 1) Vibration frequency range: 10Hz to 55Hz to 10Hz; 2) Amplitude: 1.5mm; 3) Direction of vibration: three mutually perpendicular direction including the direction of stem travel 4) Duration: Each 2hours.
2.6.3	Operation Force	The switch is placed perpendicular to the direction of the operation, gradually force in key top center of switch, measure maximum intensity when it conducted required.	260±50gf
2.6.4	Over Travel	Switch at the vertical operating orientation placement, with a force equal to 2 times according to the static load applied on the switch button the top center, measure the top moving distance	0.3±0.10mm
2.6.5	Return force	The sample switch is installed such that the direction of switch operation is vertical and upon depressing the stem in its center to the whole travel distance, the force of the stem to return to its free position shall be measured.	100±30gf.min.
2.6.6	Stop strength	Placing the switch such that the direction of switch operation is vertical, and then a static load of 30N shall be applied in the direction of stem operation for a period of 1 min.	There shall be no sign of damage mechanically and lectrically.
2.6.7	Stem strength	Placing the switch such that the direction of switch operation is vertical, and then the maximum force to withstand a pull applied opposite to the direction of stem operation shall be measured.	20N.min.

3. DRAWING & DIMENSION:

Contact Us

	NO.	NAME	MATERIAL
1	1	TERMINAL	Brass silver plating
2	1	CASE	PA66 Black
3	1	CONTACT	AgCu contact side silver plating
4	1	STEM	PC
5	1	LED	H62Y Blue

All Categories

Products

Micro Switch

Rocker Switch

Tactile Switch

Push Button Switch

Slide Switch

Toggle Switch

Dip Switch

Type-C

Rotary

Potentiometer

Socket

Circuit Breakers

The encoder

Detect Switch

Reset Switch

Pressure Switch